How To Remove Rear Axle Bearing Without Puller? – Essential Tips

We all know how important a puller is in removing the bearing of the rear axle. Even most of us think that it is almost impossible to remove the rear axle bearings without a puller.

Because the rear axle is usually a long pipe. As a result, the bearing cannot be hit from the other side. So, how to remove rear axle bearing without puller? It is almost impossible to bring it out without a puller. However, if you can follow a few small steps, you can remove the rear axle bearing without a puller. Today we will talk about that. So let’s get started.

How To Remove Rear Axle Bearing Without Puller

Why Removing Rear Axle Bearing Is Important?

For various reasons, it is necessary to remove and replace the rear axle bearing. Though these reasons are different, it is better to know the details. Let’s find out why this is important.

In Case Of Servicing

If there is a problem with the rear axle during servicing, then we have to remove it from the vehicle and completely separate everything else from it. It is important to remove the bearing too at that time. If the bearings are not removed, servicing may be facing trouble. For this, it is important to remove the rear axle bearing.

To Change Bearing

The bearing breaks very quickly. After a certain time, the small balls inside the bearing break or erode. For the reasons I mentioned, it is necessary to change the bearing only after the vehicle has covered a certain distance.

To change the bearing we have to remove it from the rear axle. After that, we have to replace it with a new bearing. This process requires removing the bearing. The removal is from the rear axle.

Is It Possible To Remove The Bearing Of The Rear Axle?

Is It Possible To Remove The Bearing Of The Rear Axle

In one sense, it is not possible to remove the bearing of the rear axle without a puller. The reason for this is what I have already given in the introduction needed to do this in this article. The rear axle is usually a long pipe. And to remove the bearing we have to hit the opposite side of the bearing. Since it is like a long pipe, it is impossible to hit the opposite side. Thus it is impossible to remove the bearings of the rear axle without a puller.

However, if you want, you can do the work of a puller with any parts without buying a professional puller from the market. In this case, you do not have to spend any extra money. With the small tools at hand, you can work as the puller and bring out the bearings very easily.

How To Remove Rear Axle Bearing Without Puller – Ultimate Guide!

How To Remove Rear Axle Bearing Without Puller

Now we are at the main part of the article about How to Remove Rear Axle Bearing Without Puller. Here we will learn how to remove Rear Axle Bearing Without Puller from the rear axle. I make the process from my idea and experience. Let’s see them.

Necessary Tools

To remove the bearing from the rear axle, you have to have some regular tools in your hand. They are:

  • One box end wrench: This is the main thing that we will use here in our bearing removing process.
  • Small Pieces of Rod: We need two small pieces of rods to make our task easy and smooth. The rods should be one long and another is smaller than the rear axle inside diameter but longer than the bearing inside diameter.
  • Thread: This will help you and all people in this process. You can also avoid this. But if you avoid thread then the process may take a long time.
  • Hammer: Another main element of the bearing removing process is the hammer. This makes our task easy and fast.

Removing Process

Step 1: To remove the bearing, first remove the rear axle cover, tires, and other items that need to be removed. I am not talking about them in this article because if they are said, the article will be much longer.

Step 2: Once everything is removed you will see the bearing and in front of you will be a situation like using a puller now. But we will not use the puller. That’s why you will take the box end wrench in your hand.

Step 3: Then tie the yarn quite tightly with the smaller piece between the two pieces of rod we talked about. This will help you to work fast and easily.

Step 4: This time insert the rod into the hole on one side of the box-end wrench. Tilt the rod to one side and place it in the rear axle in such a way that the piece of rod sticks to the bearing inside.

Step 5: This time one end of the wrench will be outside and the other end will be inside the rear axle. The situation will be like you are using the puller itself.

Step 6: Now insert a large piece of the rod into the hole on the outside of the range. Enter on both sides equally. This will help you to use a hammer to bring the bearing out.

Step 7: Gently hammer the pieces of rod outside with a hammer. You have no need to hit too hard. Hit the rod with a hammer on one side but hold the other side with the other hand. So that the piece of the rod does not fall.

In this way, if you hit the outer rod slowly for a while, the piece of the inner rod like a puller will come out with the bearing. You can use some lubricants to make your work easier and faster. Although the lubricant next to the bearing is already used.

Warning

This is a very sensitive task. So from the beginning of the article to the last part, you have to think about your own safety. Safety guards, you must be used before you start working. It is also necessary to wear hand gloves and boots. This will not harm you even if a heavy object falls on your feet from above.

Be sure to install a jack to support the car properly when removing the rear axle from the car. Also, work in places where the risk is low. Hopefully, you can easily remove the rear axle bearing without a puller.

Select The Right Surface

Removing axle bearing can be a tricky and time-consuming process. That’s why it’s essential to select the right surface – one that is both safe and easy to work with. A Jumbo Hammer is ideally suited for axle-bearing removals because of its size and weight. Using a Breaker Bar or Hammer and Nail, use caution and avoid damaging your axle or wheel hub. Some surfaces are harder, so it’s best to test the area before beginning work. Finally, always wear safety gear like goggles, gloves, and respirators when removing the axle bearing.

Apply The Vehicle’s Parking Brake

Rear axle bearing removal can be tricky, but it’s not impossible with a little bit of know-how and patience. Follow these simple steps to get the job done:

1. Apply the vehicle’s parking brake to prevent axle movement.

2. Hold onto one end of a bent wire bar, and use it to hold onto the bearing housing while you loosen and remove the Bearing Nut using a wrench or open-ended ratchet tool.

3. Replace this Bearing Nut with a new unit if necessary, and torque it to 38 ft-lb (50 Nm) using an adjustable torque wrench [or equivalent].

4. Open the hood and locate the rear axle bearing assembly. 5. Use the vehicle’s parking brake to prevent further axle movement.

Use A Car Jack To Raise Your Vehicle

Removing a rear axle bearing can be a tricky and dangerous task. The job can be impossible if you don’t have the right tools and equipment. That’s why learning how to do it safely and without damaging consequences is essential.

The best way to do this is by following these three simple steps: first, use gloves and safety goggles to avoid injuries. Second, carefully lower your vehicle onto a flat surface after removing the axle so you can replace the bearing. Third, if using a car jack doesn’t work, try to remove the axle by hand. Finally, ensure your car is stable before attempting this task – you don’t want it to fall off the jack!

Place Jack Stands Under Your Vehicle

If you’re having trouble removing the rear axle bearing without a puller, don’t fret! There are a few tried and tested ways to get the job done. The first step is to place jack stands under your vehicle in line with the axle nut axis of rotation. If that still doesn’t work, try removing each wheel well lugnut one at a time and using a socket to remove the axle nut from its hub.

Ensure the bolts that attach your jack stand are tight before driving away. If you’re still having trouble, try using jack stands to support your vehicle. With a bit of ingenuity and effort, you’ll be able to get the bearing out without any trouble.

Remove The Coverings And Trays That Are In The Way

If your rear axle bearing is starting to show signs of wear and tear, it’s time to take it to a mechanic. But first, you’ll need to remove the coverings and trays in the way so you can get to the axle bearing more easily. Start by removing the wheel hub cover and the axle bearing cover.

Be careful not to tear them off – you’ll need them later. Next, use a wrench to unscrew the axle nut and remove it from the wheel hub. Finally, remove the bearing from the axle and reinstall it on another hub. Make sure to tighten everything back up using a torque wrench. Once everything is back in place, replace the coverings and trays.

Remove The Tires

Removing the rear axle bearing can be challenging, but with the right tools and techniques, it can do quickly and without any damage. To start:

  1. Remove the tire by first removing the lug nut.
  2. Disconnect the cables and remove the bearing.
  3. Unscrew the bearing using a hex key.

Conclusion

This was all about how to remove the rear axle bearing without a puller in today’s article. I have tried to explain to you in very simple and beautiful language and have shared my personal experience. Hope this helps. Even if you don’t always have a puller, you can continue your work with these two small things. Thanks for reading the whole article. I hope now you know how to remove rear axle bearing without puller. You can follow other articles on our website to get more great tips.

FAQs

What Is The Best Way To Remove A Rear Axle Bearing Without Pulling It?

There are two ways to remove a rear axle bearing without pulling it. The first way is by loosening the bolts and then removing them with an impact wrench. The second way is through a special tool that helps extract the bearing from its housing.

How Do You Remove A Bearing From A Shaft Without A Puller?

If you don’t have either of these tools available, then the best way to remove a bearing from a shaft without a puller is to use an electric drill. Insert the drill into the shaft, turn it on to high speed, and hold the bearing while it rotates.

This will break the seal between the bearing and shaft and make it easy to remove. Alternatively, you can try using compressed air or an impact wrench. With compressed air, spray the bearing until it breaks loose. With an impact wrench, use a hammer and chisel to break the seal and remove the bearing. The last resort is to use pliers or tongs to grab onto the bearing and twist it off of the shaft.

How Do You Make A Rear Axle-Bearing Puller?

There are a few ways to make a rear axle bearing puller, but the most common is using an axle nut wrench. To use this tool, you’ll first need to loosen it enough so that you can slowly turn it counterclockwise. Once it’s loosened, you can remove the wheel and hub assembly from the car. From there, you’ll use your wrench to loosen the axle nut.

What Are Some Alternatives To Using A Removal Tool When Removing An Axle Bearing?

A few alternatives exist to using a removal tool when removing an axle bearing. One alternative is to use pliers – make sure you have the right size of jaws for the job! Another alternative is to use a socket wrench and ratchet. Another alternative is to use a breaker bar and hammer.

Can Reusing Removed Parts Damage My Vehicle’s Suspension Or Other Components?

When removing rear axle bearings without a puller, it is always best to consult the owner’s manual and contact your nearest dealership for specific information on how to safely remove a bearing without causing any damage. That being said, in most cases, reused parts do not pose a significant threat to your car.

Leave a Comment