How To Change Blade On Craftsman Miter Saw – Masterful Blade Swap

To change the blade on a Craftsman miter saw, remove the blade guard, unscrew the old blade, and screw in the new blade. If you need to change blade on craftsman miter saw, follow these steps.

First, unplug the saw from its power source. Next, raise the blade to its highest position and loosen the blade bolt with a wrench. Carefully remove the old blade and insert the new blade, making sure that the teeth are facing the correct direction. Tighten the blade bolt and lower the blade. Finally, plug the saw back in and test it out.

How To Change Blade On Craftsman Miter Saw

How Do You Remove The Blade On A Craftsman Miter Saw?

How Do You Remove The Blade On A Craftsman Miter Saw

To remove the blade on a Craftsman miter saw, first loosen the blade bolt with the wrench that came with the saw. Then, remove the outer washer and inner washer from the bolt, and pull the blade off of the arbor.

If you’re looking to remove the blade on your Craftsman miter saw, you’ve come to the right place. In this article, we’ll walk you through the steps to do just that.

First, unplug the saw from any power source. Next, locate the blade guard release lever. On most models, this is located on the front of the saw near the blade. With the release lever in the open position, the blade guard can now be removed. With the blade guard removed, you should now see two small bolts holding the blade in place.

Using a wrench, remove the two bolts and washers. At this point, the blade can now be removed from the saw. To install a new blade, simply reverse the process. Now that you know how to remove the blade on a Craftsman miter saw, put that knowledge to use the next time you need to change the blade.

How Do You Install A New Blade On A Craftsman Miter Saw?

How Do You Install A New Blade On A Craftsman Miter Saw

To install a new blade on a Craftsman miter saw, you must first remove the old blade. When you need to install a new blade on your Craftsman miter saw, there are a few steps you need to follow to ensure the process goes smoothly. Here’s a step-by-step guide on how to do it:

  1. First, you need to make sure that the power is off and the blade is not spinning. If the blade is spinning, use the blade brake to stop it.
  2. Next, open the blade guard by releasing the guard latch.
  3. Once the guard is open, you’ll be able to see the blade. Use the blade wrench to loosen the blade nut and remove the old blade.
  4. Now, take the new blade and insert it onto the arbor. Make sure that the teeth are pointing in the right direction.
  5. Use the blade wrench to tighten the blade nut and secure the new blade in place.
  6. Close the blade guard and make sure that the guard latch is engaged.
  7. Lastly, turn on the power and test the new blade by making a few cuts.

What Type Of Blade Does A Craftsman Miter Saw Use?

What Type Of Blade Does A Craftsman Miter Saw Use

The Craftsman miter saw uses a 10-inch blade. A Craftsman miter saw uses a 10 inch blade. The blade is made of high carbon steel and is designed for cutting wood. The blade has a tooth count of 60 teeth per inch.

How Do You Adjust The Blade On A Craftsman Miter Saw?

How Do You Adjust The Blade On A Craftsman Miter Saw

To adjust the blade on a Craftsman miter saw, use the knob at the back of the saw to loosen or tighten the blade.
137.248810: The blade on a miter saw is what does the cutting, so it’s important to make sure it’s sharp and positioned correctly before each use. Here’s a step-by-step guide to adjusting the blade on a Craftsman miter saw.

  1. Unplug the miter saw from its power source.
  2. Raise the blade to its highest position using the handle on the front of the saw.
  3. Loosen the blade bolt with the blade wrench that came with the saw.
  4. Rotate the blade to the desired position. The angle of the blade can be adjusted from 0 degrees to 45 degrees.
  5. Tighten the blade bolt securely.
  6. Lower the blade to its original position.
  7. Plug the miter saw back in and test it out on a piece of scrap wood before cutting your project piece.

Here’s a quick video tutorial on how to adjust the blade on a Craftsman miter saw:

Conctuation

Hopefully, you are clear on how to change the blade on a Craftsman miter saw. If you still have any questions, feel free to comment below.

FAQ


How Do You Change The Blade Angle On A Craftsman Miter Saw?

To change the blade angle on a Craftsman miter saw, you will need to loosen the bevel adjustment knob at the front of the saw. Once the knob is loosened, you can tilt the blade to your desired angle and then tighten the knob to lock the blade in place.

What Is The Best Way To Clean A Craftsman Miter Saw Blade?

The best way to clean a Craftsman miter saw blade is to use a brush or cloth to remove any debris from the teeth of the blade. You can also use a miter saw blade brush to clean the blade.

How Often Should You Change The Blade On A Craftsman Miter Saw?

The recommended frequency for changing the blade on a Craftsman miter saw is every 12 to 18 months, or more often if the saw is used frequently.

What Are Some Tips For Changing The Blade On A Craftsman Miter Saw?

The following are some tips for changing the blade on a Craftsman miter saw:

Unplug the saw from the power source.
Raise the blade to its highest position.
Loosen the blade bolt with a wrench.
Remove the old blade.
Install the new blade.
Tighten the blade bolt.
Lower the blade to its original position.
Plug the saw back in to the power source.

Leave a Comment